|
|
我前几天在网上下载了一个安装包700多MB 这是安装说明 它好象需要原盘 安装说明(以下是)不知是不是传说中的整合补丁???高人看一下
#####################
# #
# Open Falcon Setup #
# #
#####################
Contents:
I. Introduction/Overview
II. Installing Open Falcon from scratch ("The Dance")
III. Updating Open Falcon with a new Update
IV. Installation problems
I. Introduction/Overview
-----------------------------
The history of Falcon 4.0 shows that new patches and updates come out all the time. Most of them have to go on top of another patch which makes the process of installing all available patches long and difficult.
To make a Falconeer's life easier, a new type of installer has been created. The Open Falcon Installer/Updater will make it easy to install new updates or "dance" with just a few clicks. The only thing you have to do is to keep your Open Falcon Setup folder in a safe place.
II. Installing Open Falcon from scratch ("The Dance")
---------------------------------------------------------
This section applies to users who wish to make a new install of Falcon 4.0 with Open Falcon and those who wish to reinstall a.k.a. "redance".
Preparing Open Falcon Setup (you only have to do this ONCE!):
1. Extract "Open_Falcon_Beta_4.0.rar" to a safe place on your hard drive. This will create a new Folder called "Open Falcon Setup" at the destination you specified. It's STRONGLY RECOMMENDED NOT TO DELETE this folder because it is needed for future updates.
If you already have extracted all existing updates, skip this step:
Integrating all update packages into Open Falcon Setup: (do this step every time you get a new update)
1. Extract the update rar file into your "Open Falcon Setup" folder overwriting existing files.
Step-by-step installation instructions:
1. If you want to reinstall, simply uninstall and delete your existing install of Falcon 4.0.
2. Install Falcon 4.0 from your CD to any location on your hard drive.
3. Installation of your local 1.07 patch should no longer be necessary.
4. Make sure you extracted all available update files into your "Open Falcon Setup" folder (in sequential order: 4.1, then 4.2 etc.).
5. Browse to your "Open Falcon Setup" folder and run "Installer.exe". (This is the Open Falcon installation program.)
6. The installer window will show you all the packages that are available to the installer. Required packages must be installed, you can install optional packages at your discretion. Optional packages can also be installed later on with "Updater.exe".
7. When you've made your selections, press the "Install" button to start installation of Open Falcon.
8. At the end of the install process, the Open Falcon config editor will be launched. Be sure that the path points to "<your Falcon 4.0 install>\F4-BMS.exe".
9. Browse through the configuration tree and select your prefered patches.
10. When you're done, hit apply. Click "OK", then "Exit" to leave the config editor.
11. Now you can close the Open Falcon Installer ("Close" button).
12. To run Open Falcon, simply use the "OF 1.0" icon that was created on your desktop.
III. Updating Open Falcon with a new Update
----------------------------------------------
This section applies to users with an existing install of Falcon 4.0 which has been installed and/or updated by the Open Falcon Installer/Updater.
Updates to Open Falcon are named like this: "Open_Falcon_Beta_4.X.rar" (where X is a number greater than 0)
Your install must be updated to x-1 before you'll be able to install the new update.
Update instructions:
1. Your "Open Falcon Setup" folder must contain the base packages as well as all the previous updates extracted in sequential order.
2. Extract the new update file "Open_Falcon_Beta_4.X.rar" to your "Open Falcon Setup" folder (overwriting existing files).
3. Run "Updater.exe" located in your "Open Falcon" folder to update your current install.
IV. Installation problems
-----------------------------
If for some reason you run into problems installing, feel free to contact me in the Open Falcon forum and I'll try to help you.
Happy dancing!
Blueprint |
|
发表于 2008-3-20 20:16:44
